The Art of Basic Plumbing When You Install a Bathtub
The Art of Basic Plumbing When You Install a Bathtub
Blog Article
The article in the next paragraphs relating to Tools You Need to Install a New Bathtub is exceedingly intriguing. Don't miss out on it.
Setting up a bathtub isn't specifically brain surgery, yet it does need strong plumbing, carpentry, and in some cases, tiling skills. Replacing an old bath tub with a brand-new one is additionally a reasonably challenging project. If the old tub is easily accessible, the project can move rapidly; if you have to open up a wall to remove the old bathtub as well as place the new tub, the job is much harder. In either case, the task is within a home handyman's abilities, although you will require a helper to move out the old tub as well as set in the new one. See to it you have actually qualified on your own for the task as well as are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed job, it is better to think about using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This write-up will certainly assist you install a new bathtub in your washroom if you have actually already acquired a brand-new tub and also don't require to change the plan of your previous water system pipes.
Your tools and also product list ought to comprise the following:
Getting ready for the Setup
To start with, the supporting structure supplied with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you make use of all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is typically the case.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the staying water that will certainly originate from the pipes. Once the supply pipes have been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Tub
Making use of the two wood boards under its feet, put the tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the tub up until the spirit level checks out degree.
To install taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Turn on the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if needed. Load the bath tub and also check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bath tub needs to wait up until the tub has actually been utilized at the very least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Safeguard the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The previous kind ought to be connected to the tap finishes first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move enough to fracture a stiff seal, causing the water to penetrate the wall surface in between the bath and the tiling, bring about complications with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bath tub with water prior to securing, to permit the motion experienced when the tub remains in use. The sealant can split rather early if you do not take into account this movement prior to sealing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently offered on the market. It is advisable to fit the tiles utilizing water-resistant or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was shown that article on Tools You Need to Install a New Bathtub from a good friend on our other web blog. Those who enjoyed our page kindly be sure to pass it around. Kudos for your time. Visit us again soon.
Connect for clarity. Report this page